Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hello,
I just downloaded nRF connect for Desktop App, and plugged in PCA 10100 2. 0. 0 , 2023, 3.
I ran quick start, and this is what I get.
Any explanation on why...
Hi Nordic Team,
I have developed a couple applications for the nRF52833 using Zephyr and have now moved to the nRF54l15. For this new application, power consumption is...
Hello,
I need to send a file of about 70KB capacity through BLE. I send each packet as 16 bytes, I get an error 19 after about 10 submissions. I have read the answers, and...
Hello：
We have a project under development which is about real-time wireless voice transmission using the nrf24l01P，We will send 96-byte voice packets each time. We intend...
Hello, Is it possible to do a save as or copy an example to another directory/folder without having to re-link all the .c files? I am using SES 4.30c. Every time I take an...
I am developing based on 52840. I can only supply VDD at 2V. I wonder if that is doable. If the answer is yes, then how should the VDDH be connected?
The datasheet requires...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
We use nRF52840 chipset to design a BT module, and it went into pre-production now. But we found the RX sensitivity is not good. We need your help to confirm the RX sensitivity...
So I am using nRF52811 and I have noticed the battery voltage going at a constant rate and suddenly for a time of 2 mins the Voltage value (ADC) dips and it comes back to...
Hi,
I read many post on devzone, but still not familiar with programming "custom board" in my case, board from Sparkfun. My Sparkfun is correctly connected to nRF52832 DK...
Hello,
I am working to replace my BM70 with nRF52 series. So it has to be quick and simple solution. So, I used nRF52840 USB dongle as my slave (Peripheral Example code...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Is there a way to know the cause of the reset?
I connect the PC to the device and run it in debug mode. However, nothing is written...
I'm running SDK 15.3 with SD 132 and SES 4.30.
I am working with the ble_app_uart_c as the base code and adding other functions. I've gone through the app_timer tutorial...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - Chip) and Nordic SDK v.14.2.0. Now I try the SPI example and I don't know which register is adressed in the last...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
This issue is similar to below ticket with -eraseall and chiperase...
