Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi,
I am usinf nrf52832 development kit and I want to establish a secure connection between central and peripheral device.
I know one way is using pairing mechanism I...
Hi,
I am using mesh SDK 4.0.0 and nRF SDK 16.0.0. I ported the ble_app_uart_coexist example from mesh SDK to build OK for pca10056 board (nRF52840) by following the instructions...
I'm attempting to receive SMS in eDRX mode. It succeeds when nRF9160 device is left in a place without moving it.
However, when I move it to a far place like a few kilometers...
Hey..
I'm using the nRF52840-preview evk, with the Arduino camera plugged into the side connector. PCA10056_USE_FRONT_HEADER is set to 0, and I'm using the SES project....
Hello, guys!
I recently started playing with nRF9160 SiP module. nRF Connect SDK is properly installed and I am able to build the code and download it properly. I also spent...
I have a nRF52832 Breakout Board, in which i programmed using arm cortex debug connector, using Segger Emmbedde Studio. I uploaded one example from nRF5_SDK_15.3.0, the propramm...
Hello;
we are having a communication issue(a BIG one at this point) that we are experiencing with our BLE 4.0 tablets. Our device(has NRF52832) is designed to communicate...
I noticed some weird behaviour which I can repeat to do with not being able to register after reading back the ICCID.
The following after the list of commands I run on bootup...
Hi,
I'm trying to update the FW of my nRF9160-DK.
Running MacOs Mojave 19.14.6. Installed nRF Connect 3.3.0. This is the log after startup of nrf connect:
2020-01-24T15...
Hi
I've checked the two PWM examples in SDK, pwm_driver and pwm_library, they seem too complex for me to understand, does anyone know where I can find a simple PWM example...
Your download page for nRF-Command-Line-Tools is not working and it redirects to "page not found (Error 404)". I am using this link https://www.nordicsemi.com/Software-and...
I am currently working on a project where I am checking an input > 3V then passing it to ADC and increasing count based on it. The count value increases or stays the same...
I'm going to write to inquire about Bluetooth Low Energy Device Beacon which will be smallest in size and can operate with coin cell battery and also able to communicate two...
Trying to build the app from C:\Users\xxxx\Documents\SEGGER Embedded Studio for ARM Projects\nRF5SDK160098a08e2\examples\ble_central_and_peripheral\experimental\ble_app_interactive...