Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hi,
I'm using SDK 15.2. The bluetooth disconnects when I enable notifications on nrfConnect. This happens only if I increase the number of bytes to be sent. I'm writing...
hii,
i am currently using light switch example proxy server and proxy clients.
here i am using 3 boards ,2 board(node B &C) are programmed with 4 generic onoff servers...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I specify a hex file in "Project Options"-> "Debug"-> "Loader"-> "Additional Load File [1]". With this setting...
I have a question about TX Power.
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
The device operates as a “Peripheral”. Is there a way to know...
Hi Devzone!
I merged app_multilink_central and app_uart_c on central side and used app_uart on peripheral side.
I'm using 2 peripherals and 1 central now, and those can...
Are there any examples for disabling/enabling peripherals at runtime for low power purposes on the nRF91 on ncs v1.0.0?
I've seen these threads but they didn't have the...
Hi all We are using nRF9160 gone through all tutorial like GPS,GPIO peripherals,Led blinking Now my main question is How to use PSM mode and eDRX mode program for nRF9160...
I am having trouble getting the nRF9160 DK to find a network running the Asset Tracker than came in the device. It appears to reset after 15 seconds of LED 3 blinking. I can...
I am trying to read from the modem on the nrf9160 DK using the AF_LTE socket and am running to a problem with reading the response from AT+CLAC. I've chosen that command to...
I have been exploring BLE and I am using bt_gatt_discover in my zephyr-based central device (nrf9160) to list the services on a Thingy:52. I am getting the callbacks as expected...
Summary
I'm running into an issue where in certain cases peer manager reports the presence of peers, but when those peers are added to a whitelist I get an NRF_ERROR_NOT_FOUND...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
