Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
I downloaded the ncs2.6.0 version using Baidu Cloud in the China region, then set the path in Toolchain Manager of NRF Desktop, and Toolchain Manager correctly identified...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
Hi,
I just connected an nRF91 dk to nRF Cloud, which worked fine. However, for some reason the GPS says I am in Trondheim, while I am clearly somewhere else in the world...
I try to communicate with NRF52832 with NRF51822 for the example radio receiver and works well with SDK5 12 3
when I try to communicate with E73 (NRF52840) board(E73(2G4M08S1C...
How to push Initiator to resolve its private address (seen at direct_addr of adv_report) when bonded private Advertiser does a direct advertising?
I need the only Initiator...
I've followed the procedure on the nRF connect cloud to verify the SIM card and add the LTE device, only once the LED3 and LED4 blink at the same time like it was connected...
We are using a NRF52840 chip (SDK 15.3) in an application and are having issues with the startup of the board. I managed to create an example application where I integrate...
Hi. I have attempted to add an out endpoint to the HID usb generic example (only 1 in endpoint in example as it is a mouse).
However it is not working. When connected my...
Is there any UART examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
Hi, I measure current in beacon in Long Range mode. Behind 3 current peaks witch represent TX on channel CH37 CH38 CH39 there is a strange current peak, witch I don't understand...
Hi,
I can't build any samples anymore for my nrf9160-DK using neither SES nor CLI only.
I followed the "Getting started assistant", pulled the v0.4.0 version of the SDK...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
Hi,
I would like to run the radio_test example on an nRF52811 chip for certification purposes.
What changes are required on the latest sample code and project to get it...
Hi all,
Is there any example to discover the custom UUID services with pc-ble-driver c/c++? As far as I understood, the ble_db_discovery is not supported for this driver...
Hi,
i am trying to Set TX power level from application using radio_modulated_tx_carrier() function from radio tool code. But when trying to run the code, application is...
Hello,
I am attempting to set up NVS to capture GPS data received from the modem for transmission to NB-IoT after collection has ended.
I have successfully implimented...
