Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello!
I am using nrf52832 with SDK14.0 and SD 5.0.0
I have issue with Flash data storage. I am using code from example (fds_test from github)
Writting works good...
Hi,
nRF52832 uses which type of modulation technique?
Whether nRF52832 is Adatpive euipment or Non adaptive equipment . Please clarify?
Wireless module certified individually...
Hi all,
I am merging my code from Mesh 1.0 to 2.0.
I am trying to put both Provisioner and Simple On/Off Client into one board,
and then the other board is simple...
Hi,
May I ask what's the minimum reference circuitry for running nrf52810 without RF? Thanks.
Our need is as follows.
1) RF, eg, Antenna is not needed 2) GPIOTE 1 channel...
So I have my dongle sniffing for BLE packets and I can see all the advertising packets coming from the device, even the SCAN_REQ and SCAN_RSP.
But as soon as I paired the...
Hi Sir
The product is nrf52840 and SDK15, If I'd want to do following SPI operation ( CS to L ---> MOSI data {0x60, 0x00, 0x00, 0x11} ---> CS to H )
1. How to setup nrf_drv_spi_transfer...
I need to write a Windows program that talks to the nRF52840 Dongle. Is there a .dll or .lib or source code for communicating with the Dongle? I have programmed the dongle...
Hi
is the design (including schematics and pcb design) for nrf52 quadcopter is working one on the GitHub ( https://github.com/NordicPlayground/nrf52-quadcopter ) without...
Guys, i'm using a custom board with nrf52832 on it. The custom board doesn't have an external oscillator. So i'm trying to use internal RC oscillator. I am not using any softdevice...
Hi,
I want to program a NRF51822 custom board(waveshare) with NRF52DK using mbed
Can someone please help me with the tutorial
Thanks and regards
Siddharth
Hello Nordic Team
I am working on Raytac MDBT42V – 512K module. In this module doesn't have external crystal. So according to Raytac spec, it recommend to use internal 32MHz...
Hello,
I'm using BL654 module (nrf52840 inside); SDK15; softdevice s140; IAR.
In my projects I'm using peripherals: I2C(TWI), SPI. Project based on ble_app_uart example...
