Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi Sir,
I'm studying the nRF52840-PDK, and i found there are two debug connector. One is Debug in connector (P18) and another is Trace connector (P25).
As check the...
Hi!
I am fully aware on how Eddystone works. Or at least I believe so. Sadly there is some weirdnesses when I am trying to broadcast using the Nordic SDK.
So what am...
Hello , ebery one
Please let me have a question about PCA 10040.
When you connect a USB cable, it acts as a virtual drive and if you copy hex format (such as Hart rate...
I'm trying to determine DFU_APP_DATA_RESERVED and FDS_VIRTUAL_PAGES.
According to this Q&A, DFU_APP_DATA_RESERVED must be the same FDS_VIRTUAL_PAGES, if FDS_VIRTUAL_PAGE_SIZE...
Hello,
I am using pca10040 and sdk 12.2.2. I want that my pca10040 should advertise for 10 sec then it should go to system off mode then it should wake up after 20 sec. My...
Hi everyone,
I was wondering if the nRF52840 DK will have NCP OpenThread support for wpantund Linux (other than Raspberry Pi) or if it already exists. I flashed the nRF52840...
Hello ,
I want to establish a connection between the adxl345 nrf51822.
Nrf51822 is working both individually and Adxl345. I would be glad if I can provide you with necessrat...
We are building a new version of a small device with the new nRF52832. Its only external connection is a micro USB plug that we use for charging - we do not need it as USB...
Hi,
I'm evaluating a nRF52 as ble central - controlled from a windows pc.
Searching the forum I just found:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/....
Hi,
I am trying to connect 4 devices with the pc-ble-driver. Therefore I modified the heartrate example.
3 Devices are connecting fine - on the 4th connection request...
I have been using nRF51 since 2013 in a lot of product. Haven't paid a lot of attention to nRF52 series because nRF51 has been a working horse and enough for our applications...
