Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi all,
i'm using an app_timer.
I need to use three timer for debounce of three button. In my case i have to discriminate the push of three button at same time. When all...
Hello Community
I have read the following threads:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
In order to know how to discover my services, including...
Hi
Does the CryptoCell in the nRF52840 support secp256k1?
In this documentation it says at one point Koblitz curves using fixed parameters, up to 256 bits, are supported...
I used to do with the iso7816 run on nRF51822 SDK9 and S110_v8.0. However,as the BLE stack is running, the iso7816 interface clock signal is abnormal. as the picture below...
Hello!
I have the board PCA10040 (nRF52 DK).
I designed two different programs:
SPI: I'm using the SPI communication to communicate with an external sensor (accelerometer...
Hello, I am working on a project that involves the implementation of a wireless temperature sensor. so, i bought the DS18b20 digital temp sensor and tried to apply the code...
hello friends:)
i have some problem during making my products,
it's an a interface board with ble that generates UART signal for other board
and i made an schematic with...
Hi,
I noticed weird behaviour on nRF52840 when using LE Coded PHY.
Connection access address is configured as logical address 1 and it works fine when using 1M and 2M...
Hi,
Can we use nRF in vehicle to vehicle communication V2V ? And how max nodes can we have ?
As I know, the nRF don't need authentication when we send data, is it true...
Hi Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210
We want to do the EMC test of our custom board and we would like to know at least an approximation of what...
Hi all,
I'm using nRF5 SDK V12.2 to do the OTA for nRF52832 . In general, it's ok. However, if I close the bluetooth function on the phone or close the DFU app from the...
Hi there,
I'm using the PPK (v1.1.0) to measure my nRF52 DK (v1.1.1). My sample programm is very simple: set up the LFXO, RTC with 8s CC-periode and the BSP_LEDs:
const...
