Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
This is a general question I will throw out initially, but I can get more specific if necessary. This is something I see a lot in my year or so of development with nordic...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
I would like to know how to add Service Change UUID: 0x2A05 Properties: INDICATE Descriptors Client Characteristic Config UUID: 0x2902 to Generic Attribute of Nordic_HRM....
Hi - I am trying to send a signed 16bit Integer from nRF52 to iOS. Using the following characteristic reader from Nordic in the nRF Toolbox on Github (here) .
static func...
Hi there:
I found a strange phonomenon about consumption betweeen advtisement and gpio17 of 51822.
When I start ble adv while setting gpio17 to input disconnected mode with...
Hi, possibly a bit of a stupid question but here we go:
I'm developing a prototype system, which includes my own design of sensor modules that transmit their data via nrf24l01...
Hi, Nordic
I know when I program one BLE app, softdevice should be needed.
If I program esb/gazell app, softdevice is not needed.
I want to know, when I program one...
Hi, Nordic
I want to add BLE DFU service in my own app, so that the nRF52 can operate BLE DFU.
I only modify 2 places:
static void services_init(void) --> init ble_dfu_init_t...
