Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hi,
I have PCA10028 dev board and Fujitsu MBH7BLZ02 BT module.
I have successfully modified some sample code and when I flash it to nRF module on the PCA board, the...
Hi,
I ordered a few couple NRF905 a few months ago. Now I wanted to re-order a few hundred pieces the seller told me that they have "C series".
What is NRF905 C series...
Hi,
Is there a uart example for the NRF51 Dongle(PCA10031)? If not, how would I go about implementing uart on the dongle to connect to the Android NRF Uart app?
Tha...
Hii all,
I would like to create a project that take an input from any Bluetooth device and display it on display device like EPD. Till now I just hard coded the image and...
Hi all,
I have two NRF24LE1 devices, device_A for send data and device_B for receive data, the protocol data included in a 10-bytes length arrary(buffer).
In device_B...
I'm trying to understand whether my callback assigned to the data_handler variable during initialization of the Nordic UART Service gets executed in an interrupt or somewhere...
I know there have been a ton of topics about this but I've tried pretty much every solution I can think of and I cannot seem to figure out why my sleep current is consistently...
Hi,
I'm facing a very critical issue.
I need to send a time critical data from a ble sensor device to a Camera device acting as a ble central device.
Due to lack of full...
I want to send data without a computer from 3 ADC sensors.
using de ble uart.
How do I set my variable to send data?
I should use in ble_nus_string_send(&m_nus, data_array...
Hello, I am trying to follow the instruction for a 2way communication between nRF chip and the client device (cell phone). Although my chip is nRF51422/ PCA10028, I have found...
hi all:
Recently, I use nrf51822 as a central to connect some older sensor, but the ble chip of the older sensor did not use nordic, so I have this problem. I develop the...
I have the Heart Rate Service(HRS) program written in embedded c. I connected a two LEDs to nrf51822 board. One LED will start blinking when advertisement starts and other...
How do I write a value to gpregret when flashing the chip?
Basically, what I need to do is be able to detect the first time the chip is powered on so I can go into a special...
