Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
We have two nRF51822 chips ("A" and "B") connected via GPIO pins on our board, communicating via UART using the app_uart SDK module (in APP_UART_FLOW_CONTROL_ENABLED mode...
Hi,
I found this (PCA63506) Nordic Board, which I suppose is some kind of audio interface for the Smart Remote 2. However, I am unable to find more information on this...
Q: Is qualification process simplified by some sort of NRF81522+ S110 stack BLE pre-qualification (up to GATT level, what BT SIG ask for BLE devices)?
We use NRF81522 with...
After SD initialization and turning on advertising i have to send large amount of data via SPI continuously. SPI driver code initializes SPI module after SD init and advertising...
Hi,
I have an ISP130301C chip based on the nRF51822 chip.
I'm using the jLink Segger EDU to flash the chip without any problems.
But it seems like nothing is running...
Hi,
I just took a look to nRFgo to see how it generates vendor specific UUID's. It looks if they are generated completely random including the version number. According...
Is it possible to make the nRF51822 beacon send multiple packets to the devices it connects to?
The example code in the beacon kit sends one UUID, but I need to send information...
Hi guys and gals!
I recently got Evelution kit nRF51822 and I'm working on custom application with SoftDevice s110 on Peripheral side. I was looking in "nAN-36" documentation...
Hi,
we have developed a product based on the nRF51822 using Nordic SDK v6.1.0 and S110 v7.1.0.
Now we are on production and we are obliged to use the nRF51822-QFAA with...
Hello! I'm trying to program nrf51822 like a BLE device.
I'm using QT Creator + GNU Compiler + Open OCD + STlink(debugger) to create and program.
If I choose "gcc_nrf51_blank_xxaa...
I have a program based on some of the examples which runs in peripheral and observer roles. When either role is running alone it works without issue but if advertising and...
Hi,
my task is to develop a "repeater" and I have three nRF51422 evaluation kits.
For example, one of them sends a file, the second one receives it and then sends it to...
Hello,
Using the "simple_uart_get_ with_timeout",I cannot receive a "frame" bigger than 6 bytes.
Why?
while(simple_uart_get_with_timeout(1, &UART_RX[receivedBytes]...
