Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
I am trying to use the S110 v7.0.3 with a nRF51822 QFABA0 chip. I am using the hrs example from the SDK v5.2.0 ( I have changed the IROM address to 0x15000). I've got an error...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear Nordic,
I would like to implement on server side Private Resolvable address according to specs. For that I need to get the IRK that has been sent to client (central...
Can't seem to find the proper sdbc file and pack for the newest version of 51422_S210_256k for Keil 5 on either Keils site nor Nordic's. Called Keil and was told that Nordic...
In Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs project,when I add somting into this project but the now that I add dose not work!!?
//this is buzee_gpiote_init()
static...
Hi,
I am working on proximity solution app and I have to implement link loss and immediate alert service but don't know how implement it as I am a learner in this technology...
Hello
I think my question is pretty simple but I would like to clarify this topic, please:
I have read in other threads in this forum that " bonding should eliminate the...
Hello,
Actually, I am evaluating the nRF51822 using the EK. I have some questions as follows:
1- Is the S120 an enhanced version of the S110, and what is the real difference...
I use P0.2 as a wake-up pin, when the system into a deep sleep, I connected a High Voltage in the P0.2, it can wake up, but if I connected a High Voltage in the P0.2 always...
Hi
I got some questions about the RF part of the ref schematic.
1, why the bias voltage for ANT1 anf ANT2 are not the same since they are differential lines?
2, what...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
