Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
I am working with Thread on the nRF52840 and have setup a few nodes and a Border Router 1.0.0 as described in the documentation using Raspberry Pi 3B+.
My sdk is nRF5_SDK_for_Thread_and_Zigbee_v1...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
Hello,
we developed our electronics with your chip nRF52840, but we have problem with communication throught BLE. We tried our firmware on dev kit with this chip. It was...
Hello,
I am looking for wireless communication solution between two devices with a maximum distance of 5-10m for controlling a speed of the electric-assisted vehicle (basically...
Hi,
I use SDK 12.3.0 with PCA10040 board, and try running experimental_ble_app_buttonless_dfu. It works fine when I use Keil to compile, but doesn't when use GNU. I open...
Hi,
I've tried connecting to the nRF52840 Dongle using nRF connect as explained in : ://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools...
Hi, I've been trying to build a custom characteristic and so far I can display a single digit number on my BLE app. My update value function looks like this:
And my add...
I am using SEGGER Embedded Studio to program the nRF51822 module. When I was going through the manual for setting up the environment for SEGGER Embedded studio, I found that...
I want to use a buzzer on my board.
The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi support team,
I'm using a PDK(PCA10056) with nrf52840 and SDK 15.0. Recently I was developing a BLE bootloader for DFU OTA.
Since the ble bootloader was depended on...
Hi
I have been trying to get example ble_app_hrs to run after compilation on my 52832 dev board (pca10040).
The specific example is: C:\Keil_v5\ARM\PACK\NordicSemiconductor...
Hello,
after migrating from SDK14.2.0 to SDK15.0.0 I was suddenly unable to connect my central and peripheral devices. After looking into it with a Bluetooth sniffer, I...
Hey, I want to create a Mesh Monitor, to do this I want to create the follow setup:
Mesh consist of Several servers with Heartbeat message Tx/Rx enabled send periodically...
Hello,
I'm experiencing some problems reconnecting an iOS device (possibly same thing on Android) to my peripheral in the background. This happens most of the times after...
I'm using S140 6.0.0 and associated MBR on an nRF52840 with a custom boot loader derived from the nRF5 SDK 15.0.0 examples.
I'd like to perform some custom actions as soon...
