When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
I know Thingy:52-FW project has been marked as deprecated. https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
However, I'm trying to get the development environment...
Hi，
I am using the ZBOSS SDK to develop the zigbee function, and I see that there are
TRACE_MSG(TRACE_ZCL1, ">> zb_zcl_finish_and_send_packet_common param %hd delay %d...
Hi,
based on my previous post/question here and after I managed to cconnect 5 specific address devices/peripherals from my central (DK) based on filtering (solution in the...
When I want to add LTE to my project I've done this by adding
to prj.conf. When I (pristine)build (within VScode, and when using the command line) i get the following...
Hi guys,
I am using the nRF52840 until recently - with the 2t2 library from nrfx - on a Zephyr application over the latest NCS 1.7.1
I wanted to add tag write capabilities...
Hi there
prj.conf
EXR-200-004.dts
main.c
Please refer the .dts custom board file. We took a basic file generated from nRFConnect for nRF52811, and added in some missing...
Hello,
In nRF Connect desktop application, under Bluetooth Low Energy tool v3.0.0, whenever I connect a peripheral device using this application, I see the option to update...
Hi
my application is driving a RGB LED by one wire, this is request a higher sequence , when you drive the RGB LED ,this task can not be interrupt , I am use timer3 to...
Hi all,
I'm working on a project using the nrf52832 with SDK 15.3.0. Our device is battery powered and in peripheral mode. When a central connects it sends +- 300 bytes...
Hello,
I have the Icarus IoT board nrf9160, and I'm trying to connect it to the nrf connect for desktop but it doesn't seem to support the board. I'm getting the following...
