hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
Hello
My setup looks like this. I am using nrf5_SDK_for_Mesh_v5.0.0 with nRF5_SDK_17.0.2. I have extended the sensor model example (in nrf5_SDK_for_Mesh_v5.0.0) and call...
Just wanted to get clarity on the usage of RACP. In the Glucose SDK example, every measurement gets saved to the database regardless if a Central is connected or not. Why...
Hi,
[246] System: Intermittent extra current consumption when going to sleep
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was inherited...
Hello everyone,
I am new and tried some example on the nrf52840 devkit and dongle, including light switch example.
I am now going to send some ASCII bytes through the...
Hi,
The nrf52840 is mounted in our custom board. We found a Jlink programmer , hoping that this programmer is compatible with our chip(nrf52840) to flash the program onto...
Hello! As the subject implies, I'm looking for a Zephyr BLE Long Range Advertiser Example for the nRF52840 DK. Can anyone point me in the direction of one (if it exists)?...
