I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi,
for my PCB, i'm using an NRF52832 as SPI slave, i send an array of 4 bytes {0xA5,0x00,0x01,ff}, but my SPI master receives always a byte (0xff) before 0xA5.
this...
Hello everyone
I have kind of a basic question.
I'm not sure how to manually disconnect from a ble connection. I'm using the ble_app_uart and ble_app_uart_c examples from...
Hey all,
We’re trying to figure out the best way of keeping our nRF52 (or 51) based design in the lowest power mode possible while sitting in inventory.
Currently, our...
Greetings,
I have 12 sensors each of which is located on an nRF52832 board. I need to collect the sensor data at 50Hz (10 bytes for each sensor).
For some reason I can...
This one is throwing me for a loop.
We just did a small build of 40 devices based around the nRF52832. 1 device out of those 40 is behaving very strangely. When the device...
Hi Sir
I want change the power transmission level for measuring the RSSI values for different configuration from -40DB to 4DB. for that i configure the radio. But it is...
When compiling (after the project folder change and paths updating) I get always this error.
No idea why. The C99 option is choose
It compiles correctly from SDK tree...
Hello,
I just finished migrating my project from SDK13.1 to 15.0. It caught my attention that when I flash the Softdevice, it uses memory from pages 0x00000 - 0x24000. I...
I think I found a bug in nrf_ringbuf_cpy_get. The first memcpy is wrong. The source and destination should be swapped.
if (length > trail) { memcpy(&p_ringbuf->p_buffer...
Hello,
I am using the NRF51822 in a low power application and need to transfer the data from the PCB (with the NRF) to the PC over Bluetooth. I need the biggest possible...
Hi,
I would like to know if there is any reason that tx_power is limited to +4dBm in the Mesh examples. I am using an nrf52840 and it is capable of +8dBm. Would it increase...
I am starting afresh, and have only just downloaded & installed Keil v5.25, nRF SDK v15.0.0, and nRFgo Studio v1.21.2.10
So everything should be "latest" and "up-to-date...
I am working on small UART project. I am begineer coder.
I want to transmit 0-9 numbers using UART. I am using nRF52832 board and IDE using is Eclipse pca10040. I applied...
Hi,
I am using nRF52832 pca10040 developement board. As I am begineer I dont know much about coding. I am using Eclipse IDE for developement. I want to transmit 1-10 numbers...
