Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Description: Hello,
I am integrating a Protocentral MAX30001 ECG sensor with the nRF52DK (nRF52832) using the nRF Connect SDK v3.1.1.
The Issue: The sensor hardware is...
Hi,
I'm developing a Matter device based on the Window Covering sample. I have added another endpoint to the device containing some sensor clusters and it all works after...
Hi,
I am looking for a constant-time memory comparison is a function that compares memory for equality in a fixed amount of time, regardless of the data's content. I am...
We're currently developing a zephyr firmware on zephyr 4.2 and we got a custom board for our hardware powered by an nrf52840-ckaa-R
the first time I connected the board...
Hi all.
I've attached a single channel microphone onto my nRF9151 and I'd like to capture blocks of audio for processing. I've configured the device tree like this:
i2s...
Good evening.
I am working on a USB HID joystick. The USB documentation on nordic, while better than the woefully inadequate zephyr mainline docs, only covers the surface...
Hi,
I'm designing my device based on the Thingy53 layout and I have some questions:
The first is why, in the T53, the antenna division comes through U17 (PE4259) instead...
I recently began testing with the nPM1300EK and it seems like something is wrong with it. A number of different tasks don't seem to be working correctly:
Profiling a battery...
Greetings,
Using SDK v3.1.1 the SPI MISO signal appears to be actively driven by the nRF5280 for both my SPI1 and SPI2 configurations. In both cases there are no active...
Hi All,
I have to validate following use cases:
N reflector with nrf52833
1 initiator with nrf5340
The nrf5340 will be able to :
calculate distance from each...
Hi,
we are implementing MCUmgr SMP OTA over BLE (Zephyr + nRF54L15) with flutter, and I want to confirm that I’m generating the correct SMP upload packet format before streaming...
Hai, i try to MFRC522 rfid reader interface the nrf52833. 1. I try the read version from reader but it's only show the 0xFF 2.I try to read the card id . it is not work. I...
I'm unable to import/export mesh networks and then subsequently send mesh messages. I believe this problem has been mentioned before [ 1 ][2][3], but the solutions offered...
Hi,
We've had a mesh sensor network all working for a long time using SDK17.0.2 + Mesh SDK 4.1.0
The data is accessed by a mobile app through a mesh node acting as a proxy...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
