Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I have developed a custom application on nRF54L15 and now I want to add OTA over BLE support in it.
For that, I am following Exercise 5 – FOTA over Bluetooth Low Energy...
I am trying to setup the dev. environment in OpenSuSE Linux, but, even though it says Linux, I only find support for Ubuntu.
I am blocked now setting connecting the board...
Hello,
I'm designing an application where I intend to authorize different users to access the functionalities of a device based on the nRF54 family.
The general idea is...
Hello, I'm using NFC Type 4 Tag (T4T) but I can't write to it. The tool I'm using is the nRF NFC Toolbox. From the app screen I generate a Record and then touch the tag to...
Good day, I'm trying to use pin 1.02 as a GPIO in a TF-M build using a (custom) non-secure board target, and I'm struggling to find the appropriate way to accomplish this...
When I first created the BLOB Transfer model, I had to analysis the DFU sample code because there was no BLOB Transfer model sample.
Is it possible for me to create a sample...
Hi, For supporting multiple different peripherals is it possible to get something back from a SoC observer which indicates the peripheral type? https://docs.nordicsemi.com...
We have a manufacturing project assembling the 0.35mm CSP package. We would like guidance on part handling, solder stencil specifications and any other process steps that...
I am developing a DFU (FOTA) feature via BLE on the nRF54L15 MCU using NCS v2.9.1 .
I am using MCUBoot direct-XIP with revert mode .
My application needs to detect the...
Hi Nordic Team,
I’m working with the nRF9160DK , specifically targeting the nRF52840 application core ( nrf9160dk_nrf52840 ).
While building a BLE Central application...
Hi Nordic team,
We’ve implemented a custom firmware update flow for our nRF5340-based device , which supports a robust single-image FOTA process using external NAND flash...
In our design, we wired the SD card in SPI mode on SPI bus 4 wich a maximum SPI frequency of 50 MHz or 25 MHz as these are supported by the SD card. We used FAT32 file system...
Due to board design flaws that led to insufficient rise time for 100kbps communication, I would like to configure my i2c node in the device tree with a baud rate of 10 kbps...
Hi, I previously saw in open threads that it was possible to retrieve I/Q samples from the BLE chip inside nrf9151 DK in order to save them. I would like to reproduce this...
