Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I have nRF54H20, SDK 3.1.0
is there any sample (tested) which is running with high speed peripheral? I need to test high speed SPI (SPI120 or 121).
I found (....
I am trying to get an end to end BLE application working. I have an nRF52832 board that is running peripheral_uart. It is advertising and sending a text stream to the connected...
Hi Nordic support
We have ealier used your legasy SDK16.0 on nRF52840 where we where programming our device serial number in the UIRC area.
NRF_UICR->CUSTOMER[0-4] where...
Dear,
I was trying to flash a custom board using a nrf5340 module (Raytac MDBT53-1M) threw P20 connection of a nrf5340-DK like described in https://infocenter.nordicsemi...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello, i am already 1 week trying to make tracing working. I have NRF54L15DK and SEGGER J_TRACE PRO. I solder trace port on the board.
I did enable => nRF TPIU in nRF KConfig...
I've tried to compile "hello_dect" example using v2.6.1 toolchain and v2.7.0-rc-2 SDK. The sample code is present so I assume the SDK is correct version. However it fails...
Hey folks, I'm trying to use SPI00 instead of SPI20 to achieve higher frequencies and driver fails to initialize no matter what I've tried to do on NRF54L15-DK. Here are relevant...
Hello,
I have 9 sensors based on NRF54L15 working as GATT server. I push around 100 bytes every 15ms from all sensors to the central hub. When i connect all nine of them...
Hi everyone!
I am developing device based on nrf25833 mcu which should transmit data to android devices using ble characteristic notification mechanism (data received...
Hi!
Recently I bought this device (v1.1.2) and I was very happy about it until I tried to verify the current and voltage readings. Tried two multimeters and they both agree...
I am porting and existing app to nRF Connect SDK 2.7.0 from 2.6.1. Using sysbuild, MCUBoot and the app are building and I am able to load the firmware onto the PCB and it...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
Hi Is it possible to configure project to use simultaneous multi image DFU and serial recovery over USB? I would like to be able to update both cores using dfu_multi_image_XXX...
