Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi, I have several services running in the application. one of them is DFU.
I have to hide / stop DFU service for example when the SOC of the battery is less than 50%. And...
Hi,
I am working on nrF52832 as a gatt peipheral (server)and have a requirement to send 12KB of data over a custom service. I have done the following:
1. Created a custom...
Hi Nordic:
1. Does NRF9160 modem 1.3.1 support CSQ command?
2 Is there a command to get SINR signal?
3. NCSv1.8.0, modem1.3.1 %XRFTEST (AT%XRFTEST=2,1,0,0) Can it can...
Hi,
we're performing an evaluation of using an nRF528xx module with 802.15.4 stack to replace a 3rd-party radio module. There will need to be an AT command protocol for...
Hi i am using nordic nrf52840 chip. and SDK17.1 i am using.
in that under secure bootloader code i am trying to use the nrf_crypto_hash_update() function to calculate...
Hi,
We need to update the firmware of the device through IOS-nRF-Connect-Device-Manager, but the language currently used in our old project is objective-c. IOS-nRF-Connect...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
