Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm calling nrf_drv_uart_rx_abort() in order to read partially captured input from UART in my event handler.
However, instead of receiving a NRF_DRV_UART_EVT_RX_DONE event...
Hello,
We are currently developing a project based on nRF52810.
We are testing some examples to learn more about this chip.
Now we would need to know which signals and...
Hi,
I have gone through this ticket --> https://devzone.nordicsemi.com/f/nordic-q-a/30104/how-do-i-share-private-questions-with-my-coworkers-using-the-new-devzone
But...
Hi,
I am using NRF52840.
After upgrading to SDK 17, I found that the chuo stays in boot mode because this new condition (I highlighted it in the code below):
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET...
Hi
I have some questions.
I'm trying to communicate with BLE using 9160DK with my smartphone.
1. Do you have a simple example? 2. Can I send videos or pictures using...
Hi nRF support team, By using the nRF Connect SDK, I am trying to create a timer, which I can use for incrementing a counter by 1 for each second on a timer interrupt handler...
Hi,
I am trying to merge the ble_app_becon with dfu. What are the things I need to add. In becon example I don't find the services_init() function. Do i want to include...
Hi,
I am using the latest SDK, with the nRF52840.
using the usbd_ble_uart example.
Created a timer that starts to send packets to the PC throw USB with a running index...
Hi Dev Team,
I have an iot.1nce.net sim that I am using in Germany.
+CGDCONT: 0,"IP","iot.1nce.net","10.205.84.3",0,0
I was trying the eDRX configuration using a basic...
Hi,
The ' nRF52840 Errata Attachment Anomaly 172 Addendum' linked to in the nRF52840 errata (Version 1.3, page 17) seems to be missing; the link gives a 404 error. Where...
I've tried to test the ZigBee OTA example on the 4.1.0 SDK, but it does not work. I've gone through the exact steps of the procedure as described in the infocenter, but it...
Hello,
in our project we have a nRF52840DK as central (s140) and a custom board with nRF52832 chip as peripheral (s132). The software on the nRF52840DK is based on the ble_app_uart_c...
When I program the Zigbee cli example from T&Z SDK v4.1.0 I see that the Zigbee stack uses some flash areas at the end of the chip. In my case 304 bytes @ 0x000F7000 and 24...
Hello,
Using libuarte I have been able to set up UARTE0 and UARTE1 for main communications, and debug communications respectively. While using UARTE1 to print out debug...
Hi,
I's trying to implement switch two application firmware in the openbootloader example, but I meet some issue.
I change the sector to 0x27000 in App1, 0x40000 in...
