Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi.
Can you make a youtube video showing how to use SEEGER studio for a demo project.
I would like to see the whole workflow starting with a new project for nRF91xx where...
Hello,
I'm developing an HID consumer control application with the nrf52832. As many ble products have, I would like to add a power off button to my pcb. Is it better to...
I'm just after C headers and Makefile like the NRF5 SDK.
All I found was some "AppImage" file for x86_64 which I've no idea what to do with - I tried unzipping it, but it...
Hi!
Whenever I open an example for the nrf52833 (PCA10100) in SES I get the error "The evaluation period for this release has now expired". This does not happen when I try...
I am working on nrf52832. For my task, I need to knoow how nordic find out the Total average current on Online Power Profiler for BLE( https://devzone.nordicsemi.com/nordic...
I wanna try to connect multiple device with only one Android, but I don't know how many devices Ble can connect to only one Android. When I try demo on Samsung galaxy S8,...
Hi,
I have an issue that is urgent for me, as we wish to add DFU capabilities via pre and post production hardware. I am using Android 10 on Samsung Galaxy A10 to test...
Hi,
I was able to create a device driver support for a DAC, model TI DAC80501Z. In the first place I put the driver in zephyr/drivers/sensors.
I works fine.
Then I made...
Hi Team,
Please provide the nRF52 based module Characterization, software testing for FCC/IC/ETSI certification test procedure and document
Is DTM test enough for FCC...
According to SDK documentation for GFX library :
“After generating a font, you must change FONT_INFO::height to be described in bits (pixels), not pages”
But in the provided...
Hi,
I can build the blinky_pca10040_s132 example and I loaded it in the nrf52840-DK without errors but nothing happens in the bord I can´t see any lead blinky.
Please...
Hi
We are sending devices for RF/wireless testing and need test firmware that allows for the Bluetooth frequency and transmission power to be easily adjusted. Does Nordic...
Hi.
As you have made a progress in your development of both hardware and software. It would be greate if you remove old videos from youtube. I have just spent some time...
Hello.
I am using nrf52832 and Segeer Embedded Studio.
I want to add a timer function to the ble_app_uart example so that the sensor value is read every 50 ms.
So I...
I am trying to build nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_uart for the PCA10100 DK.
I am using DFP 8.32.1.
I get the following warnings:
RTE\Device...
