Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
i have a complete project based the gfx project and i want to add BLE using UART for communication. i want to communicate my module with the nRF52840 dongle.
is there simple...
SDK14+NRF52832.
I used one timer to do something every millisecond. and I used another function to do a loop action, the function maybe breaked if the time period exceed...
Can not connect Android 8 mobile phones, such as HUAWEI Nova 3
Nodic equipment is not even found.
We cannot connect with official UART routines.（ble_app_uart...
I found a terminal that can not communicate with BLE. I think that the sequence after MTU exchange is strange. The program used is sample HRM. The terminal used is "Xperia...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello, I am using the nRF52840 dev kit. I am using SES to develop the code for it. I want to include the bosch bme680 library in my code. It comes as a libalgobsec.a file...
The objective is to have a device which constantly advertises some status information - this must be always visible to any Central in range.
The device may connect to at...
I inherited an active project with regrettably little support from the previous developer.
I have been trying to download a copy of the application firmware that I generated...
I try, DFU by USB-SERIAL on NRF52840-DK. I installed SoftDevice S140 V6.1.1 and open_bootloader/pca10056_usb (SDK15.3) Python2.7.16/nrfutil for windows was installed. My DFU...
I am trying to keep an output pin asserted while I jump to the DFU on the 52840.
We have a dead-man switch hooked up to pin 19. I need to hold this pin high while I jump...
So we are using NCPTransport from nrf-util (nordicsemi/thread/tncp.py) to have CoAP connectivity over Thread NCP from Raspberry Pi to other Thread devices. We have a use case...
Hi,
I am trying to install pc-ble-driver-py pypi lib into custom yocto setup. I have created recipes for it which is shown bellow
in python-pc-ble-driver-py.inc
...
Hi. Im working with an application that uses the s110 softdevice and i want to use the s130 to be able to recive advertisereports but when using the s130 Everything stops...
Hey everyone,
I've got an nRF52840 DK on my hands. There's an interesting crash occurring when the return value from ble_nus_data_send() is passed to APP_ERROR_CHECK()....
I am using several Laird BL652 units on a project. They contain a nRF52832. For the most part they are working great, except I have one that only works some of the time and...
