Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
I use the light ctrl example from NCS 3.2.4 on the 52840DK v3.0.1, serial communication with an external MCU is required. After suspending the UART and disabling Mesh...
Hello, I was wondering when will the new nRF54LM20A/B series of SoCs will be available to build as a new board based on them? In the current version of the nRF Connect for...
Hi there. I am trying to use the RISC-V core with a custom code to take a picture. In a separate project it is working with MBOX and communicating the image pointer in memory...
Hi
I'know there already exists some tickets regarding getting the version number of the software running on the net-core but they are old and do not answer my question....
Dear Nordic experts,
I am looking for which CMSIS version are used in nRF5 SDK versions. For instance 17.1.0 uses CMSIS 5.6.0. But I cannot find which CMSIS version is used...
I want to change the BLE advertisement TX power output.
I can already do it via the prj.conf file,
CONFIG_BT_CTLR_TX_PWR_ANTENNA=-4
but I need to change it on-site during...
I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
Hi everyone,
I need to implement a coded Phy ble communication in a project and for that I wanted to use an nrf52840 dk. However, for it to be able to compete with the Aircable...
Here are results of running the bluetooth sample central uart, first when built with target nrf9160dk/nrf9160, and second with build target nrf9160dk/nrf9160/ns.
*** Booting...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Hi, We currently update firmware using the official nRF Connect app with a .bin file over BLE, and that works for us.
Our team needs to implement the same DFU flow in our...
We are experiencing critical data integrity issues on the BLE link of our gateway device. The problem occurs specifically when the device is operating as a BLE-to-Wi-Fi bridge...
Hi,
Any specific reason the errata Anomaly 166 : https://docs.nordicsemi.com/bundle/errata_nRF5340_Rev1/page/ERR/nRF5340/Rev1/latest/err_340.html resolution patch as present...
Hi,
I am facing a strange NB-IoT connectivity issue with the nRF9160 in Dammam, Saudi Arabia.
Setup
SDK version: v2.5.0
Toolchain: nRF Connect for SDK VSCode...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
