I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Dear, I defined Port1 pins as in attached overlay file. The binding of pins is done as in lcd.h attached file. When, build is started, the error written in title is displayed...
Hi,
for a last year I was developing any apps for nrf52840 in Keil IDE. Now I'd like to migrate my projects to VSCode but still do not understand some curcumstancies:
...
Dear NCS experts,
I'm working with NRF Connect SDK (1.7.1) on a proprietary Bluetooth Mesh model. When the model receives its configuration, it stores it in flash by calling...
Hello,
I am evaluating the DK52 board and have a problem with the reset button. Before the problem occurred, when I powered up the board connected to my windows 10 host...
Hello,
We have designed a product with NPM1100. With the NPM1100 set to output voltage of 3.0, we have measured the output across multiple devices to be in the 3.1 to 3...
Hello everyone , I am interfacing and trying to process GPS data received over UART port. The GPS outputs NMEA based sentences at a rate of 10 Hz. I started using the example...
I've tested two scenarios using a hardware loopback to test UART functionality. The double buffer approach does not work as expected.
SDK version 1.6.1
CONFIG_SERIAL=y...
Hi,
I used nRF91DK for almost 2 months non stop to debug the final nRF91 based board for our air quality monitoring hardware to fight the propagation of Covid virus.
But...
I tested various copy methods in terms of instruction cycles, that I determined with DWT.
For that I copied an uint8_t array size 70 by
for Loop --> 63 Cycles
memcpy...
Hello,
I am using nRF52840 dev kit with sdk 17.0.2, s140 softdevice and dfu bootloader also implemented.
When I download the firmware to dev kit it works as intended...
Hi,
i am working on nRF52832. i am facing a issue of RESET when i call advertise_start() again after advertise duration. in debug it shows fatal error.
Hi there,
I've installed and followed the nRF Connect SDK manual install getting started guide ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
I'm using 52832 as a Central(SDK_17.0.2/S132_7.0.2), and sometimes get a connect-disconnect failure with reason 0x3e.It happens randomly and frequently.
I search the forum...
