I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I just used the nRF Connect Toolchain manager to install the NRF Connect SDK. Then, the Segger studio keeps popping this error when I try to open a project:
And...
Hello,
From the nrf91dk datasheet, a stackup is provided. Because it looks custom, and I'm having a hard time finding a manufacturer that can do that stackup. What PCB...
hi，
I read the data manual of 52832, but I have some questions about the following parameters, like CM_FLASH,CM_FLASH/MHZ,CM_FLASH/MA,please explain it in detail and what...
Hello ervery one,
I am doing development on NRF52840. I have a problem as follows looking forward to your guidance.
I need to jump to Application 2 (address: 0x32000)...
I See in the discussion that I can see I/Q for AoA.
I see this examples "direction_finding_connectionless_rx" on zephyr I Think that I can start debug using the data from...
I want to transfer a few bytes of data between two NRF52 modules.
I have checked out the BLE Blinky and NUS example and understand the gatt client and server ideas.
My...
Hello.
I am using SDK version 17.0.2.
The example code uses nrfx_spim . Target board nrf52832
The nrfx_spim project confirmed that 10040 did not exist, only 10056...
hello,
in the case
Case ID: 227777
https://devzone.nordicsemi.com/f/nordic-q-a/46439/turning-services-like-hid-on-off-without-disconnect/309149#309149
In the...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
