Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello,
I’m struggling with a problem and need your help. I have an application where a nrf52840 communicates with another nrf52840 over BLE using nus and some services....
I am about to follow the steps here https://wiki.segger.com/Open_Flashloader to be able to program an external flash. However if there is an easier method I would prefer to...
Hello, i would know about the IDE avaiable to develop codes for SoC Nordic nRF52840 and where i can find/download it
Moreover, where can i see examples code about BLE Client...
Hi
I'm working with FreeRTOS with Tickless (RTC) and I was wondering what one should do in order to avoid the FreeRTOS Idle Task to be waken up every time an Interrupt Service...
I have installed SES 5.10a and imported ouf Keil project. There are several issues when I try to compile. This is interesting since I am using the "external" build which should...
Hello,
I have products based on NRF51822, that are central and peripheral.
These products use Softdevice S310, bootloader and application code. It use peer manager, fs...
Hello,
I'm pretty to new to developing with the NRF52 and the NRF52-DK and have a couple of questions.
I have a custom board which has an integrated NRF52832 chip. Now...
Hi,
Recently, I've found a reset issue with my device by ble_nus_data_send error when ble is working.
But the error code is 0x3401(Please, refer the picture). What does...
I'm working on augmenting an existing product that is based in the nRF52832. We've been using a handful of timers for some time without apparent issue. I added another timer...
Hi,
We are using the modem firmware V1.2 and source code ncs v1.2.0. Problem: we are using the TLS connected socket to amazon cloud and after about 12 minutes of doing:...
Hello,
I'm a beginner in NRF52832 module.
I want to test saadc + bluetooth communication.
So, I searched
https://github.com/NordicPlayground/nRF52-ADC-examples
this...
Hi,
Is there any way we can measure performance on nrf5340?
We have an IRQ event handler for ISR and we see that whenever the event handler is invoked, main function...
Hello,
i have a strange issue with my analog input. Every few seconds (not the same database) my signal is getting pulled low.
But i dont know why. The external signal...
I been having an issue using the ZB_ZCL_REGISTER_DEVICE_CB to know when the ZC writes to an attribute that is of type 0x42 String type. It seems that the callback id changes...
Hello,
Whenever we reset our custom board with the USB cable plugged in and powered, the NRF_POWER->USBREGSTATUS has a value of 1. It will not go to a value of 3 ( OUTPUTRDY...