Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
We have a custom radio protocol that manipulates the radio registers directly (on the '32) and I'm evaluating whether or not we can switch to the '33 to use it's angle of...
i have used a example of ble_app_template in ble_peripheral of SDK15.0,when code run in ble_advertising_start,return errcode 8.
i have checked low speed Crystals，it's ok...
I get error 0x3401 in ble_app_uart_pca10040_s132 (nrf52 dk, sdk17) in ble_nus.c line 95:
err_code = sd_ble_gatts_value_get(p_ble_evt->evt.gap_evt.conn_handle, p_nus->tx_handles...
Hi,
I've been using the python bindings for the pc-ble-driver and have been getting things to work, but I noticed there is no API exposed for reading the RSSI of a connected...
I am using nrf52811, SEGGER Embedded Studio and I want to use Beacon demo. I click Build and Run , it prints as below:
And I can not find the beacon device in nRF Connect...
Hello,
We are planning to buy the BWG840F BLE to Wi-Fi gateway.
https://www.fanstel.com/wifi-ble-5-iot-gateway
It has the nRF52840 module (BT840). We have the nRF52833...
Environment:
Segger Embedded Studio
nRF52840
S140
Windows
nRF 5 SDK 17
Hi,
I'm developing a device for a small side project. I need to get logs in both the...
I am trying to integrate MAX30003 drivers in spi_pca 10040 example, So that I can get the sensor readings of the MAX 30003 sensor. But I am stuck at this error.
When I...
Hi,
I am using nrf52 development kit . I connected peripheral device and communicate all characteristics using DK.
But i want read rssi value from peripheral. I didnt...
Hi,
Do do you know of any Xamarin Development being done using your development kits?
Trying to determine the best way to get up and going using Xamarin vs native iOS...
Hi there,
Just wondering why serial_uartes example has been removed from SDK17, We have to use 2 uarts at the same time.
Is it intentional or accidental ?
Thanks,...
Hi everyone. I'm using a Thingy:91 and the asset tracker application. I can compile and flash (using SES and a Segger J-Link) the application and the device connects to the...
Hello,
I read your white paper nWP-030 about selecting the decouping caps. But I didn't find any explanation why you also specify maximum values for the caps. Especially...
Hey,
I am using SDK12, S130, nRF51822;
Trying to create a DFU update for application which Also writes over a certain area in the reserve app data, in the end of the designated...
