Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi everyone,
I found that I can log the CPU persantage usage here . I have enabled the NRF_PWR_MGMT_CONFIG_CPU_USAGE_MONITOR_ENABLED but I do not know what steps I have...
I am working with a proximity beacon example. In that runs scanning and advertisement code, And in testing, most of the cases, I am not able to get the Advertisement packet...
hello ,
I would like to know what is the use of m_in_boot_mode global variable in BLE mouse example, m_in_boot_mode updates it value in a handler called on_hids_evt, so...
Hello,
I'm trying to program the Makerdiary nRF52840-MDK USB Dongle with the Bluetooth sample project central_uart but when I load the built HEX file to Programmer file...
I'm on my Windows 10 machine using Segger Embedded Studio V4.52C. I'm using SDK16 and Mesh 4.0.1 with FreeRTOS. I have built the light switch server example found here to...
Hello,
I am using SDK v1.3.0 with modem firmware v1.2.0 with the nRF9160 DK v0.9.0. I am using an AT&T SIM card to connect to their LTE Cat-M1 network.
I would like to...
I’ve not yet been able to successfully get an application (in this case Blinky) to complete a BLE DFU load and then execute. I’ve tried all the suggestions I’ve found in the...
Hello,
I would like to learn a little more about the possibilities of thin planning of connection events. I rely on chapter 15, in particular on part 15.7 of the S140 SoftDevice...
Hi, I'm trying to do the iot mqtt publisher example with the nRF5_SDK_15.3.0_59ac345, a nrf52840 and a Raspberry Pi 3 B+ as a gateway but I got some problems :
After the...
We have been testing the DK board and Thingy:91 and had a few questions on enabling PSM/queued mode.
We are able to enable queued mode for the lwm2m_client example on the...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi!
I'm going over the nRF52820 chipset, and I'm not sure I completely understand the reference schematics in regards to the LC filters on the REG1 DCDC enabled option....
I am using "ble_app_hrs_rscs_relay" example and modified it a bit by adding NUS service and FDS. Everything is working fine with mobile app and nrf dongle. How ever when I...