When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi Nordic team,
I have a simple HID BLE device which send volume+/- multimedia keys to a Android device, it works
well if it is first time to pair with the Android device...
I'm developing a project that use BLE advertise and uart communication with other uC.
The uart part is based on libuarte example. To decrease the current consumption, I...
I am trying to do spp communication between central and peripheral with BLE.
First, the peripheral uses microchip RN4871.
The BLE setting is Service UUID: 49535343FE7D4AE58FA99FAFD205E455...
Hi,
I've been trying to run the zephyr's littlefs sample on Thingy:91 under the ncs 1.2.0 tag, but it seems that the flash_open_area function is having some trouble, and...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
When I am going to program a custom board for the first time, can I use example codes from the SDK or should I change anything important on the configuration?
On my custom...
I'm trying to create a simple service that would just provide some data which could get updated internally (for example, via SPI bus). Data may be of a different size, so...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hi,
I'm just getting started and tried to run the lwm2m_client sample from the v1.2.0 release of the nRF Connect SDK which I assume is the latest stable version? However...
hai ,
in my apllication i am using nrf52840 , i merged a code code of peripheral and central (app_blinky example)
i need to connect a peripheral to central (with esp32...
I'm working with the nRF52840 PDK and I'm wondering how to change the PHY (preferably to CODED) in a Mesh. Has that been implemented yet? Or when can we expect this feature...
When developing the dfu upgrade device, the code can be loaded to 100%, but the prompt "remote dfu invalid crc error" The compiled firmware can be upgraded with the old nRFtoolbox...
Hello,
I'm trying to get the PCA10056 to communicate with the MPU6050 Motion Processor (I think that's what it's called), but still in the very starting point.
1 - I've...
I've been using STM32 controllers with LoRaWan mostly GNU based and bare metal. Recently, I have been looking at the STM Nucleo STMWB32 communicating with a Raspberry Pi and...
