Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
Hello,
Not a 100%, but in this Nordic video the nRF52840 might be using the Alexa Gadgets Toolkit. Alexa Notepad demo 2020 https://www.youtube.com/watch?v=CdLfg-6kQs0
...
Received our 52840 DK, loaded, via nRF Go Studio, s140_nrf52_7.0.1_softdevice.hex. Loaded, via IAR Workbench, ble_app_blinky_pca10056a_s140. I clicked to go button and whamo...
Hello. Nordic team.
Once again I had questions, this time related to serialization .
While the preparation of the driver is on the PC side, I am studying the examples...
I have an issue with reseting the board using a hard reset via an external button. The onboard development kit reset works, but I am trying to perform the same task using...
Hello,
I was reading the nrf_libuarte_async library, and noticed that in the
app_timer_handler -
calls the
local_app_timer_start -
again and starts the timer again...
Hi,
I use a 3rd party board from raytac ( https://www.raytac.com/product/ins.php?index_id=95 ) on my PCB and I have problems with a bluetooth low energy connection. On your...
Hello,
I'm trying to get sleep mode working on a nRF52840-DK with Zephyr or Mbed OS while using UART.
It is possible to achieve low current consumption in sleep mode...
I opened an example from the SDK 16 in:
nRF5_SDK_16.0.0_98a08e2/examples/iot/lwm2m/lwm2m_client/pca10056/s140/ses/iot_lwm2m_client_pca10056_s140.emProject
When I try to...
Hello!
I want to develop my own app, and the source code refer to proximity in nrf toolbox. Now, i have some questions:
1. What function in the source code of serverManager...
Hello
In my application, I would like to allow smartphone that are Bluetooth V5 compatible to receive more information in advertinsing packets from my devices (via the ...
Hi,
I want to optimize the transmission efficiency and thinking of sending larger packets than 2048 bytes of MQTT would help.
We have limited battery power, and looking...
Hi,
I am started working on nRF9160 Power Management. I want to power down all devices(sleep mode) expect motion sensor, Wake if motion is detected. I went through System...
Hi Team,
Can you please point me where I can change the compiler optimization level in SES v4.52 and I am using nRF9160 module.
Regards,
Praveen Palaparthi
Hi Team,
We are using the NRF52840 Device with S140 Soft device for our BLE applications. As part of this we have enabled the flash storage as well.
We are unable to write...
