I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
How do i use a single serial port to communicate with the server...
NRF52840 development board does not have any programs when burning into bootloader and application and protocol stack and settings.hex,
Why do you need an OTA to enter the...
The questions are related to nrf9160:
How much memory space is currently used and free on the Thingy:91, nrf9160?
How much memory would take a complex timing routine...
I'm working nrf52832 , SDK V15.3.0 and S132. I have implemented whitelist in application and its working fine. I need to add one phone as master device so i need to hard coded...
Hello,
I'm using nRF52811 SoC with nRF5_SDK16.0.0 and SoftDevice v7.0.1. I'm using following code to write data into flash. This code is tested with nRF52840 in both debug...
i want to interface the adxl345 accelerometer with the nrf52840 board
i got an code from ADXL375_12C.zip
https://devzone.nordicsemi.com/cfs-file/__key/communityserver...
Hello All,
Is there an explanation why the Pin Configuration Registers are not available for viewing in the Registers view of Segger Embedded Studio?
If there is can someone...
Hello,
We have an nrf9160 dk-pca10090 board.
We want to know if there is a way to make the two processors (nrf52840 and nrf9160) communicate using uart.
Kindly...
Hi everyone
I have a question about zigbee. After reviewing the documentation, I realized that on the nrf52840 chip, you can use zigbee with a frequency of 2.4 GHz. But...
Hi, First of all, appriciate all your hard work on tech supporting, this is my first ask in this forum. I m currently using developing nrf52832 on Zephyr , working on the...
I'm trying to integrate mesh 4.0.0 into an existing project that uses sdk 16.0.0. I'm very close, but I'm getting an error when I try to run mesh_stack_start()
I traced...
HI everyone,
I am currently facing an issue when using nrfjprog to flash my nrf52832-based custom board using nrfjprog.
Here is the steps I followed:
- Creating application...
Hi,
I have recently been evaluating the nRF52840 for the research purpose. I came across a question related to this product that I could not figure it out myself.
I noticed...
Hi Nordic
Is there any sniffer can sniffing ANT traffic?
I just trying 52840DK and nrf-sniffer-3.0, and read user guide, it seems to sniffer BLE packets only.
Regards...
Hello Supports,
I downloaded the SUPL package, and extracted it to nrf/ext/lib/bin/supl/.
For enable it in gps example, I set CONFIG_SUPL_CLIENT_LIB to y in prj.conf...
