Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi Nordic,
I build the nRF UART 2.0 application source code running on Android OS 5.1 and it works well, but android 10 cannot scan the device.
I migrated to Androidx...
Hi,
Some questions regarding passkey and Diffie Hellman.
When a device connects to a mobile - the mobile user should insert a passkey.
Does this passkey used as a...
Hi I am developing a Multi-link Central that connect to a mobile phone and multiple BLE dongles. I use the Multi-link and BLE blinky in SDK 17, it works fine.
My problem...
Hi all,
I tested with example uart_pac10056 (SDK16), but return error NRF_BREAKPOINT_COND.
When i debug, it show error in APP_UART_FIFO_ERROR.
Could you show my mistake...
Hi All,
Is it possible for me to broadcast multiple&different type of beacons/advertisement, for example ibeacon, eddystone, unconnectable-advertisement, connectable-advertisement...
Hello, I would like to use the pc_ble_driver_py with sd api v6. I can see in the CMakeLists.txt where I can change set(SD_API_VERS "2;5") to set(SD_API_VERS "2;6"), and it...
Application Info:
I am working on developing a synchronized mesh network of low power sensors. I am trying to maintain an average power consumption of 100's of µW while...
Hello, there,
I am trying to get the UARTE working on a custom nRF52840 board. In my setup, I am expecting a response to every transmission on UART.
Here's my setup...
Hello,
Would appreciate current-day thinking regarding unused GPIO pins. Our product uses Laird's BL652, which embeds the nRF52832. Many GPIO pins are unused. I've looked...
I am new to nRF9160 development board. I have just opened the board and tried to connect following the startup instructions. I was able to see LED 3 and LED 4 blink the first...
Hi,
I am trying to get a bootloader to work on the nRF52832 and struggling to get the application to run after a DFU. I could not get this to work on my custom board and...
First of all, thank you and kudos to Nordic Support Team for having an awesome and functional forum.
Having said that, I have a question related to the architecture of mesh...
Hello,
I am trying to analyse my project my source code with sourcetrail (give graphics with calling functions).
During indexing task, some libraries are not found like...
Hello,
When I run the ble_app_template application from the examples, sd_app_evt_wait() cause an error and the app to crash. So I've put my project in debug mode (DEBUG...
After successfully running the GPS and acquiring position the application goes into an infinite wait loop when attempting to start it again, but only if either or both of...
