Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Today I was playing around w/ my nRF9160DK 0.8.2 and messing around w/ the Asset Tracker application. I edited the proj.conf file in order to attempt to get it to connect...
I want to read data over uart from sensor, advertise the value go to idle mode and wake up on rtc timeout to do the same thing again.
when I try to read data over uart from...
The nRF52832 chip and SDK12.3.0 implement the buttonless DFU function.
First, as you are guided by the DK board, you have already completed the tutorial.
I tried to run...
nRF52832_XXAA, nRF SDK 14.0.0, SoftDevice 132 v5.0.1
We run a single service with 2 characteristics: one for "target to host" and the other for "host to target", where the...
Help ！
I use ANCS need change ATT MTU to more , but I met an incredible thing .
just change NRF_SDH_BLE_GAP_DATA_LENGTH to 189 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 185
...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
As i an trying to establish LTE connection using nRF9160.but i want to use external antenna because i will place nrf9160 module in metal enclosure. please suggest best antenna...
Hi pals!
I'm trying to do the throughput example with using 2 nrf52840DK. I downloaded SDK15.0.0 and I'm using ble_app_mtu_throughput example under ble_central_and_peripheral...
Hello there,
I've been following a guide Installing a 6LoWPAN enabled Linux kernel and required modules as a part of setting up a BLE 6LoWPAN border router on Raspberry...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
Hello everyone
I am using nRF52840+wifi module to communication with the server via MQTT+LTS, Now MQTT communication with server was successful, Considering the safety,...
Hi everybody!
We have a problem with our product. It is based on nrf52832.
We used heart rate example in the SDK. MCU sleeps after a while if it is not connected. We have...
I'm trying to combine conventional pairing with OOB NFC pairing, but I'm struggling to decide which libraries to use. I have been looking at the examples, and they all use...
