Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
I built this ( devzone.nordicsemi.com/.../Nordic_2D00_Thingy52_2D00_FW_2D00_master.zip) Nordic Thingy SES project and downloaded the generated hex file in Nordic Thingy. Now...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
Hello,
I have recently built and flashed CoAP Sample on my board.
After that the device cannot connect to the mobile network.
Could you please provide me a description...
Hello,
We have finished the development of a prototype device that incorperates the nRF9160 SiP. I would like to know if there is anything I need to set-up in the device...
Hi,
I would like to use hal_time_get() [hal_timer.h] in my project, and I try to add below library into Makefile.
but I got an error. "error: implicit declaration of function...
i am using/ ble_app_multilink/ example present in central folder..i am beginner to this ,,so i have few doubts in it
1)so where actually advertisers(which are advertising...
Hi,I had a problem with nRF51822 DFU.I tried to OTD nRF51822( version SDK_9.0.0 s110 ) wiht Android 9.0 devices( nRF tool version 1.9.0 ),but it always fail at 1%.The problem...
Hello fellow Nordic-ians,
I am developing a custom firmware for Nordic Thingy 52. I am using the Segger Embedded Studio as my IDE and J-link Edu Mini as the programmer ...
Hi,
I have found zboss 1.0 opensource.
Surveying the source, i have noticed that variable "g_zb" (nicknamed by ZG) give system informations.
I can find zed address(16bit...
Hi,
Here is my setup, NRF52832 PCA10040 s132, sdk 13.0.0.
I work on Windows 10 with a server (The aim is to do it from a Raspberry later) which one is connected to my...
