Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
In any of the documentations, I could not find the Antenna Gain of the nRF52840 development kit. Could you please point out to me where I can find Antenna Gain or any...
Hi,
On NRF9160DK, there is a nrf52840 chip.
I want to use nrf52840 as a host controller with NRF9160, but I cannot find any example to control nrf9160 by nrf52840. ...
Dear support team & community
Our company tries to integrate communications between our NRF52840 -based product and a Philips Hue Bridge gateway. We successfully connect...
hi ...
how to merge the serial uarte and ble_app_uart .... i want to getting the data through the serial uart and i need to transfer the same data over ble .. please guide...
Hi,
I have implemented a hx711 sensor readout with PPI, using SPIM and PWM peripherals. But for this is needed 4 GPIO and one external OR Gate. I wait for a LOW pulse on...
I came across the nrf-connect SDK sample UART : https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c . I was wondering whether...
Hi team
I want to config interval via LL_CONNECTION_PARAM_REQ.
But nrf5 looks like use L2CAP CONNECTION PARAMETER UPDATE REQUEST to send request to change config.
But...
Is there any reason the pin reset hold time is not mentioned in the nRF52832 product sheet? I've seen in the forums that it is same as nRF51, which is 0.2 uSec but I would...
Hi
We are using BL600-SA in our project. I need to configure NRF51822 transmit power so that it is discoverable at particular distance.
I am using softdevice S110 and...
Hi.
I am newbie and trying some sample examples from nRF52832 SDK for mesh to gain knowledge of Bluetooth mesh
I have nrf52832 Development Kit and I am trying examples...
Hi! We're developing a BLE-sensor for tracking small animals. In the past we've used a different brand of BLE-module but we're looking to switch to the nRF52840. As we're...
I want to use my "nrf51 DK" module as a BLE sniffer for which guide is provided at https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf but I also need " nRF Sniffer...
Hello,
I cannot connect Thingy91 to NB-IOT or LTE-M network. I am in the UK, so I am trying the NB-IoT with an O2 sim card. In LTE Link monitor I am unable to get a connection...
"There was an error adding your device. It wasn't found. Is it connected?"
IMEI and PIN entered several times.
I do not want to post the ID's here.
By the way: HW...
