Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi:
I am having trouble just trying to build the asset_tracker_image.
I followed the instruction on setting the nRF Connect. (nRF Connect v3.2.0). However I got the following...
Hi,
When I reference of SDK Coexist examp of uart for adding in Experimental dimming example.
I get success in it.
I take dimming level from uart, and publish it via...
Hello,
Just received the nRF9160-DK and followed instructions but it seems there is no connection, only LED3 is blinking
Location is Belgium close to Brussels
Hi,
I'm using the PCA10056 dev kit to verify the workings of the DCDC converter. I added the following code after nrf_sdh_enable_request() :
e = sd_power_dcdc_mode_set...
Hi to all,
I'm new with the nRF52 DK developpement board and I use Zerynth ( Python ) for developping a simple application for a product who are still existing. ( MOKO M1...
Hello,
I am developing in Windows 10 machine in visual studio code. I cannot use Seggar studio. Devloping for nRF52840 dongle with nRF15 sdk.
I have written the below...
I am using SDK12.3 and the Flash Storage module to store some data in Flash. I frequently need to update some of these data basing on received commands.
When I use "fs_erase...
Hello,
we are developing a machine that is in pre-production. We need to be able to update the firmware and until now all works well on android. but on IOS the dfu does...
I'm trying to get the LTE Sensor gateway running on the nRF9160 DK. The documentation says to run the HCI:UART example on the nRF52840. When I click on the link for that example...
Hi,
I need to know if it's possible get the firmware work using 52810 with 192K flash. As far as I know, S112 takes 100K, APP with secure connection takes ~85K(ble_app_hrs_pca10040_s132...
nrf52832 S132 v6.1.1
i want to write saadc data in flash, so i call "write_to_flash" function in "void saadc_callback(nrf_drv_saadc_evt_t const * p_event)"
sizeof(data_array3...
Does anyone know if Segger Ozone is licensed for commercial use if used with Nordic Semiconductor devices, similar to the use of Segger Embedded Studio? Or, do we need to...
Hello Everyone,
As mentioned above I wanna know how to send Energy Expended data from nRF51422_xxac device to BLE mobile application using HRM characteristics or HRS Services...
Hi,
I'm starting to work with Nordic Semi Develoment boards with a Thingy:91.
And I wanted test the GPS module and send it over HTTP POST using the LTE of the Thingy...
Dear,
I am using :
ncs: v0.4.0
SES 4.16
firmware: mfwnrf916007029alpha
Hardware: nRF9160 DK v: 0.8.5
I want to do:
1. Enable and get GPS position ("AT\%XSYSTEMMODE...