hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I merge saadc and ble_uart together in order to send send sensor output(now just analog voltage) to mobile app. I want to check weather the ADC is working properly or...
Greetings to all,
I'm using nRF52840 with the latests SDKs (nRF5 SDK 15.3.0, mesh SDK 3.2.0). I have two questions which are related-
I'm trying to find a clever way...
I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I am looking for (andriod) mobile phone that support Bluetooth LE coded (long range)
Have you ever tested bluetooth (LE coded) with mobile phone ?
Please recommend...
I am currently developing firmware that needs to run on both 32 and 40 chips.
The basics of the situation is the firmware contains 3 'applications'. A flag in the UICR region...
Hello,
I have been looking through the SDK for the Thingy:52, and I have been unable to find the configuration file used for the MPU-9250. I am able to see the default pedometer...
I use QSPI to access MT25qu512 serial flash and find the following behavior.
SDK: nRF5_SDK_15.3.0_59ac345
QSPI configuration:
// Use 4 bytes address from serial flash...
I am unable to figure out what causes the problem that IRQ handler is defined both in nrfx_uart and nrfx_uarte modules.
After investigating in a test project I have found...
I have previously built the Asset Tracker downloaded it to my 9160DK with no problems.
Today I connected my Thingy91 and updated it's firmware. Afterwards I built the Asset...
Hello,
I'm trying to create a Mesh network with the following devices:
* Mobile phone as provisioner (supports PB-GATT only)
* Two different bulb's which supports PB...
When storing entries that aren't multiple of 4 bytes they are padded with random bytes by flash manager.
The problem is that they aren't padded with 1's but rather random...
I'm testing with a Custom board using a nrf52832 chip.
Testing BLE communication using nRF Tool Box.
I am using SDK15.3.0 example for communication using nRF Toolbox and...
Hi,
I am trying to install the nrf command line tools on linux. After following the installation instruction, I have the error
ERROR: nrfjprog.ini not found. Please reinstall...
