Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi, I'm using the nRF52840 Preview DK to get data from a digital microphone via a PDM interface. I'm using a clock frequency on 1.032 MHz to activate the microphone. The data...
Hi,
As discussed in this ticket we need a way to reduce the current consumption.
The LPN example doesn't solve this for us.
Our application is based on the light switch...
Hi, we have the latest Xcode installed on our new development Mac (up to date iOS too).
When we downloaded the iOS nRF toolbox from git hub today we get errors when compiling...
Hello Everyone,
I am looking for an Eddystone example. It should be used for an nrf52 with s132 SoftDevice (programming with nrf52 Prev Dev Kit).
Thanks for help
I'm struggling with how to properly identify an unprovisioned mesh device. Basically when i scan for unprovisioned devices from my iOS app, I'd like for only our devices to...
If I use sdk12.3 pca10040 S132
softdevice is s132_nrf52_3.0.0_softdevice.hex
How do I determine what version of Bluetooth it is?
In SDK or where the document has instructions...
Hi, I had download the nRF5_SDK_15.3.0_59ac345,but I couldn't find the softdevice S112 hex.(Nordic52\nRF52_SDK_Source\nRF5_SDK_15.3.0_59ac345\components\softdevice\s112\hex...
Hi ,
We have the following setup :
One nrf52840-dk acting as a multi-link central
One nrf52840-dk acting as a peripheral ( blinky app )
Both communicate well over...
I want to expand the Asset_Tracker example by adding the possibility to send data through UART2 to the controller and then to the nRF Cloud.
I am unable to find any document...
for 52840, customer want to have a part of flash, it can set write protect, to avoid illegal erase or destroy, they use this part of flash to run boot-loader, is it passable...
As far as I could see, only GGA NMEA sentences are enabled by default. I want to check if RMC sentences deliver positions faster, and in my prj.conf I do the following:
...
I got an nRF52 DK and I was unable to recognize the JLINK driver by connecting to my computer via USB. My SEGGER version is 6.44E and my own jlinkV9 is normal. How can I solve...
hi all ,
now , i need add create mqtt ble gateway .
it compiler failed follow message :
C:/temp/ncs/zephyr/drivers/serial/uart_nrfx_uarte.c:1272:9: error: 'DT_NORDIC_NRF_UARTE_UART_2_LABEL...
