Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Dear helper.
Currently, in my custom board had a GPS chip that connect to nRF52832 with UART port.
But also the only way that I can trace the log is the other UART port...
Hi
I have custom board with nrf52832. I have lion batery and 3.3V ldo for powering device. I attached shematic.
For preventing lion battery decreasing below 3V, i used...
We're thinking about implementing a machine learning algorithm in our nrf52832 based product. Before starting implementation, I would like to estimate the power consumption...
Hi.
I would like to route the BLE SPI signals to an external connector for use with external debugger.
Please specify which the nRf52832 pins are by default assigns to...
Dear Nordic Support Team,
I want to integrate ble_app_uart_c and ble_app_multilink_central into a nRF52840 as an edge gateway, and the nRF52840 node communicates to the...
I try flash read, write and erase with flash_fstorage_example sdk 15 on nrf52 dk
On main.c i can write and read with nrf_fstorage functions.
When i try nrf_fstorage_erase...
I try to use SDK15/FreeRTOS project.
I measured current comsumption on IDLE state(not run any task).
It's take about 200uA.
On FreeRTOS's portable/CMSIS/nrf52/port_cmsis_systick...
Hello there,
I purchased some NRF52832 Development Kits and some NRF52832 Standalones. I wrote some code and flashed it to the development kit and it worked. Otherwise,...
Hi all!
I'm using the fanstel board. I can see that the "ble - uart" examples run ok.
In the code the configuration assign to P06 (Tx) and P08 (Rx) , when i look in the...
I'm implementing an application which uses the Secure bootloader with bonds. What happens if I create a bond to a device in application mode and then switch to bootloader...
We are designing a circuit that will be supplied from lipo battery, vddh. I am wondering how decoupling capacitors on vdd will impact as it is suggested (in errata 202) to...
We are using pc-ble-driver-py on our Ubuntu host machine which is connected to the nrf52832 running connectivity firmware and we are able to run the examples, how could we...
Hello,
I have got a quick question regarding a potential workaround-setting for the BLE_HCI_DIFFERENT_TRANSACTION_COLLISION-error.
Here is what I am currently seeing:...
Here i am attaching the my working code of the application.in my application i am using the two peripherals one is TWI and onther one is UART.i interface some sensors with...
I have a wireless project. Requirements as:
Support platforms: Desktop/Laptop and mobile, Pc/Mac/IOS/Android. etc.
many connections: flexible but can support 100+...
