There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
I want to write at the end of memory ROM data in address 0x7FFFF
uint8_t tst_arr[1] = {6};
sd_flash_write((uint32_t*)0x7FFFF, (uint32_t*) &tst_arr, 1);
Is it correct...
Hello ,
System configuration
Set up 1 Adafruit BLE Feather running stock central UART example from NORDIC SDK version 15.0`examples connected to host PC using USB
Set...
The dedicated NFC pins on the nRF52840 are P0.09 and P0.10. However, these are noted as "Standard drive, low frequency I/O only " pins, with "l ow frequency I/O" defined as...
Hi, I'm facing an issue after provisioning the Client and Servers from Light Switch example of Mesh SDK 2.0.1, using the Android App. Provisioning is successful, however,...
Hello,
Following on from this question , I've been trying to identify the source of unexpectedly high power consumption when using the RTC. In order to test this, I am using...
Hey all, I am using an NRF52 DK and am trying to combine the 'pwm' and 'ant broadcast' examples. Both examples compile fine on their own, but when I try to combine I am getting...
I have a number of (probably naive) questions regarding the internal temperature module on the nrf52832.
1) Regarding the FICR values for temperature. Are these programmed...
