Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I just tried the example from
github.com/.../nrf52-mpu-easydma-using-gpiote-and-registers
And they are working like a charm. Now I want to change the example...
In the on_ble_evt(ble_evt_t*) function from the ble_app_template, I added a case of 'BLE_GATTS_EVT_WRITE'. In it has the following code:
case BLE_GATTS_EVT_WRITE:
{ ...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
Hello dear Nordic Semiconductor!!! I took your wonderful Thingy:52 everything was great until I wanted to build a project based on your Thingy: 52-SDK. I have nrf52840 pdk...
hi, i am having a doubt. now my nrf 52840 is acting as a peripheral. it is advertising some packets and my mobile is acting as a central and receiving the advertising packets...
Hi there,
First: I’m a newby, just did some things with Arduino to control some LEDs etc but not much more before.
What’s my plan: I actually ‘ld lik to control some...
I am new to BLE development and have started by installing SEGGER Embedded Studio
Release 3.30 and have a J-LINK edu usb device and a Core51822 board from Wavetek.
I understand...
I am using various sensors to build a wireless sensor network. There are libraries for sensors that are provided by developers such as from adafruit or sparkfun. I have been...
What is the easiest way to use Arduino libraries into nrf52 projects in Keil on C?
Arduino has a lot minus : bad ide, not support debug mode, not optimize code size. But...
I work with nRF52832, based on SDK 14.0.0, and I have done DFU operation successfully with nRF connect on iOS, but when I used Android phone, nRF connect couldn't start DFU...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
