Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Dear Nordic company,
I am writting to you in order to discuse some trouble with TCP server that I am trying run on Serial LTE modem application.
I am able to create...
Hi everyone,
I am currently studing to flash the MDBT50Q-DB-40 demo board from RAYTAC. I used the following site as reference. https://docs.nordicsemi.com/bundle/ncs-latest...
I'm trying to flash a custom board (schematics in this ticket - Schematic/Layout review request ) using a Jlink EDU mini and keep running into an error message saying it's...
Hello,
I am currently measuring the current consumption of the Thingy:91, specifically when running the Asset Tracker v2 application. I observed that the average current...
Hello, I’m currently working on a PDM microphone project using the nRF52840 and the Zephyr RTOS. I’ve been testing the official dmic example from Zephyr (located at ncs/v2...
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Sending array unit8 type data using BLE failed, and attempting to take 2 bytes of data from the array and send it also failed. Does anyone know what this log error means?...
Hello,
Since a few days ago, when I start VS Code, I get the following warning:
But when I check the settings in VS Code, v1.x.x is not there.
What could be the...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
I am currently working with the nrf54l15, I have both the DK and a custom board I designed. I am running into issues with the uart00 peripheral when using custom GPIO pins...
Hi,
I am using nRF52840 DK and I am following Nordic Academy nRF Connect SDK Fundamentals. I installed SDK 2.9.1 and toolchain 2.9.1
I copied the sample blinky and encountering...
Hi everyone,
I'm using the nRF54L15-DK and trying to implement a simple low-power cycle where the board:
Measures sensor values
Sends them via CoAP over OpenThread...
I am migrating from a child_image type project to the newer sysbuild system used in ncs v2.9.0.
My application is based on the ncs nrf5340_audio application, but my application...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi everyone,
Environment setup: - I am using Zephyr OS 2.5.0 running on nRF52840 board. - MIRA mesh integrated in the application.
Problem description: - Firmware A has...
