When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I would like to move the SDK12.2 template example project out of SDK12.2 installation directory. How can I do that using uVision5?
I tried to change all the reference...
Hi
I don't understand how to correctly flash all three parts so that the app runs on boot.
At the moment if I flash them all the nrf51 (51822) boots to the dfu bootloader...
I can see in the latest SDK 12.2 that signing of the dfu firmware files is possible.
Am I right in thinking that this signing verifies the source of the firmware files...
Hi, I have nrf51822QFAA series. I am using S110 for softdevice which takes 96KB. My current program size is Code=31908 RO-data=512 RW-data=312 ZI-data=8360. I want to know...
Hi.
I am using the new SDK 13.0.0 and nrf52 chip. I am trying to set a whitelist with
the peripheral_template example code.
I think the whitelist is already enabled in...
I have made an ADC driver that (should) scan 5 inputs into a sample buffer using EasyDMA. On the END event the 5 samples are transferred to 5 ring buffers read by the client...
I've tried to upgrade the firmware using the DFU feature of the android nrf-toolbox app, but it returns the "REading file failed" error.
this happens only with my phone...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...
Hi everyone. I am working on a project while doing my undergrad in EE and am confused on a few things.
I am using Raspberry Pi 3s with the NRF24L01 (NRFL) chip and code...
Hello!) Have some problem with custom pcb, created for nrf52832. After mounting all components a connected pcb to nrf52dk through P20 port. Chip was correctly detected in...
Hello,
I faced the problem of high power consumption when using a large number of the inner periphery.
Currently used:
SPI1 -> Accelerometer, ext. serial memory
TWI0...
