Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
My device is smart watch. We transfer some data to phone and receive notification from phone over BLE.
My question is those two functions(connect_params_init and sec_params_init...
Hello
I'm new in the world of nordic semiconductor and I've a little problem. I would like to transfer ANT+ data of a HRM Garmin in serial protocol to my PC. I use a nRF51422...
Hi,
I transmit a data packet to AP2, i wonder if it needs a sequence for resetting or not while AP2
initializing.
And, I send a packet data to AP2 by UART(AP2...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
