hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi nRF support team, By using the nRF Connect SDK, I am trying to implement an SPI communication with the display module from my nRF52840 dev kit and nRF52840 as a master...
Hi,
we have the need to implement the border router functionality for 6loWPAN in our device using a nRF52840.
Essentially we need to replace the Raspberry Pi in your examples...
Hi, everyone,
I'm trying to assign an SPI End Event to a DPPI channel on nRF5340dk to trigger a counter automatically. However, the value of the counter never increases...
Hi, I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1 (latest if I am right). nRF52840 DK as HW. I want to...
I need to collect data from approximately 20000 points. I want to form a BLE mesh network and collect the data. The sensors may be buried below the ground level about 30 to...
Hi all,
I have a problem with nRF52840 acting as TWI slave. I'm using TWIS. Typical scenario is:
1. Master writes request and ends transaction using stop condition.
...
Hi,
Scenario: 1 Thingy52 device and nRF52 Development kit is in a mesh network, where Development kit is connected to PC via usb cable and also connected to J-Link application...
With the release of SDK For Mesh v5.0.0 the mesh_stack_power_down() was introduced.
When calling mesh_stack_power_down() an assert was hit in nrf_mesh_timer_tail_handle...
Hi
I am using Mesh SDK v4.2.0 and I want to add Simple_On_Off Model to the Light_Switch example and provision and configure it with the provisioner example.
So far I have...
Hi,
I have been using NRF52833 DK for many applications - such as get a battery voltage - which was great using SDK. Now, I moved to my own PCB which has got NRF52833 chip...
I Figured it out. You can delete this question.
Hello,
I am using MBN52832DK development board which have nrf52832 on it. I am using ble_uart_app and I can communicate...
I am working on a project now that will be performing ssl based http or websocket connections to a server.
I have looked around a little and seen some documentation and...
Hello,
I'm using zephyr to develop a battery powered IoT device with a sensor and a LoRa transceiver (SX126x). And I'm expecting to achieve average consumption values (during...
