Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching/231773
We found sometime the LTE cannot be deactivated during the modem...
I want to try register level programming of Nrf52832 i.e low level programming. I referred your This GitHub repository but there are sill some libraries used . Is there any...
I am running an application with norma NUS Service with bonding.
When I want to make a DFU I start to write a token into the flash with fds and then do a soft reset. After...
Hi, I'm using nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 to develop a Zigbee Network. I'm using the ble_zigbee_template example as starting point of my works. I seen that...
Hello,
I have an nRF9160 DK and a Thingy:91. Both have been running asset_tracker for more than 3 hours, but none achieved an LTE Connection. I have installed the latest...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
Hi,
I am working on buttonless dfu example, but i want to design my application in such a way that, device should enter into dfu mode when button is pressed. I should be...
Hi, I have some issue about mesh network.
Using below developing environment.
- SEGGER Embedded studio for ARM V4.22
- nRF SDK 15.3.0
- nRF Mesh SDK 3.2.0
- chip...
Hello
I'm a beginner in Bluetooh and I bought two dev board NRF52840 DK. I would like to make a mesh with these two boards. One in master and the other in relay, the goal...
Hi,
I´m working with "TWI Sensor" example of SDK 16 and I modified the Main function of main.c as follows (just added NRF_LOG_INFO("\r\ntest") );:
I just added this...
Is there a good way to uniquely identify mesh node across multiple smart phones? The problem is: Android provides access to MAC addresses that can be used as identifiers of...
Hello. When I examined the BLE data format, I found that it was as shown in Figure 1.
Fig1
I am using NRF52832, please tell me how to detect the CRC value...
