Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
Tried the 2.0 nRFSniffer hex file today. It does not show up in WireShark like
the Beta 3 version does, "nRF Sniffer COM6". Tried on two devices with the same result...
My application just hit the following fault randomly:
I tracked back in the map file and that is inside the Nordic NRFX library in ipc_trace_handle, so I have no source...
Is it possible to have discontiguous Non-Secure areas in SRAM to be used by the application?
&sram0 {
reg = <0x20000000 DT_SIZE_K(8)>;
};
&sram0_ns {
reg = <0x20002000...
Hi There
Here we have been encountering some problems and would appreciate if you could help.
We are designing the hardware based on the following schematic, please...
Hi!
Just want to ask if anyone have had the same issue as me, when flashing nRF9160 with J-Link V6.50.
In SEGGER Embedded Studio - Build -> Build and run || Target ->...
Hello!
I use a usb secure bootloader with MBR (without SD) for update my application via USB. Also, my application receives new firmware via GSM modem and saves it to an...
I'm using pc-ble-driver to talk to the nRF52840 dev-dongle from a Windows PC. I started with examples\heart_rate_collector\main.c I receive events in a function 'ble_evt_dispatch...
Hi all,
I want to use the nrf51dk to answer and reject phone calls. One button on the kit would be used to accept calls and another to reject or finish them. The audio...
Hi dear team,
I am using the nRF5840 Dongle and pc-ble-driver-py for development, but I encountered a lot of issue while debugging, I thought I used wrong parameter or other...
We have worked through getting AWS MQTT working and have the FOTA job file loading properly. When the HTTP request is made the file begins downloading but fails to download...
Hello, How do I program the NRF52840 module to read and write data with a single UUID, because the mobile application I used earlier was working with the data read and write...
Hi Nordic
I am trying to run the AWS BLE FreeRTOS demo found at:
https://docs.aws.amazon.com/freertos/latest/userguide/ble-demo.html#ble-demo-mqtt
I am using an...
Hi,
I am developing a product with battery power. To preserve the battery life, this product needs to work in low power mode.
My Environment is a nRF52832, SDK15.2 & custom...
Here S332 -ble_ant_app_hrm file is modified using supported board pca10040 (nrf52832).
There is in pca10040.h file,RX pin number & TX pin number predefined.
And we use...
