Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...
Hi,
Is there a tutorial or guidelines on how to send ble-app_hts data to nrfcloud mentioned in this Noridc video below.
Nordic Semiconductor - nRF Connect for Cloud (youtube...
We have an implementation where we need to limit data, and to be able to KNOW how much is actually being sent with the operator, to limit costs.
In a normal Ethernet condition...
Hi Nordic,
I am trying an application where both central and peripheral devices are based on nRF52.
I have to create custom services and characteristics for the same....
Hi, I am beginner for nRF51822. We are using SDK v10 and S120.
We have an IOT Gateway with it's processor interfaced with nRF51822 radio through UART. We have flashed nRF51822...
Hi all, We always have -4Mhz Radio Frequency Interference when using nrf24l01 and nrf52832 chips.We use nrf24l01 as a slave receiver, and use nrf24l01 or nrf52832 as a master...
Hello,
I'm trying to set up my nrf9160 Dev Kit and I'm having problems connecting it to the nrfCloud.
Since I'm using it in Austria, I'm using a different sim card on...
can somebody help me on how to enable twim0..
it was no problem in twi_sensor example...now i am integrating twi_sensor in ble_eddystone...and on built it give an error...
Hello,
We have a bit of a problem out here while using SPIM3 for Data transfers.After a Data transfer is initiated through direct register read, or EASYDMA and data is...
