Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
When I try to connect my device(iOS Application) to my peripheral(BLE Device), I want to send this passkey programmatically during the connection. I'm using BleManager but...
Hi,
a dumb question. For a board with voltage regulator installed is it allowed to connect SWD VTref to the regulator input (at <VTref1> point)? It's assumed that VTref...
Hello all
I've read various other threads concerning this topic, but I still can't wrap my head around it.
What I think I understand of this topic:
ATT_MTU can be...
Hello,
I'm trying to configure two TWI slave devices on the same TWI bus on my custom board(nRF52832). One slave is RTC, and the other is a biosensor. The TWI configuration...
Currently, I am using SES for development. So when I use the "Build and Run" option in SES the program runs properly. This also generates the .hex file in the Release folder...
I need to set HEX value (uint8_t value[7] = {0x56,0x45,0x52,0x53,0x49,0x4F,0x4E};) on my custom character to be read by my phone. but the value that is displayed on my character...
Hi,
1. I have been trying to measure the current consumption of the development board of nRF9160 in PSM mode, however, until now I could have not understood the role of...
Hi all,
I'd like to pass bootloader version (2bytes) from bootloader_util_reset function (bootloader) to the main of application. can help me to acheive that?
Thank...
Hello,
We are facing recently an issue that is very weird because it is not occuring every time. Indeed, the issue occurs after a DFU update, sometimes when the application...
My nrf51 DK Board is not detected by Keil as jlink probe, but with other tools. As a result I am unable to download demo projects to my board.
unmodified nrf51 dk has...
I'm working in SDK 14.2, and trying to send a single byte over SPI between two NRF5 boards using the SPI peripheral examples (1 master and 1 slave). However, SPI always seems...
Hello!
There are no hex files that are pre-made for the ble_app_interactive example. When I use VMware to run a Linux environment on Ubuntu to get an executable with gcc...
Hello,
I want to configure my nRF52840 development kit for counting input pulses on one of the GPIOs (Pin 13) in this case. I am using SEGGER Embedded Studio as IDE.
Here...
Hello,
we have a strange proglem with nrf52811 on an own board
after uart initialization and connecting the scope (Saleae) probe to the RX pin the device outputs fatal...
