hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
hello
I have questions.
1) T he difference between start_tx_carrier and start_tx_modulated_carrier Are both start_tx_carrier and start_tx_modulated_carrier sending data...
Hi,
I have gone through nrf connect app in google playstore . But when I scan for the beacons, the app gives hex values. I want to develop a customized app that will read...
Hello everyone,
I tested ble_app_beacon example code in SDK15.2 on nrf52810 scanner using nrf connect apple iphone(ios). set APP_COMPANY_IDENTIFIER 0x0059(Nordic id) its...
Does the 2nd argument in the following function SAADC example controls the sampling frequency? If this is not the case then can this saadc example program be modified to be...
If I set CONFIG_SPM=y I can flash merged.hex and successfully call sys_reboot(SYS_REBOOT_COLD) to reboot the system.
If I set CONFIG_SPM=n (and build/flash the SPM project...
I'm using nrf52_SDK_12.2.0, SoftDevice S132 for my application.
I'm implementing SAADC along with UART in my application. I was implementing the SAADC referring to the example...
In regard to the problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/38048/bug-in-how-bootloader-treats-gpregret , it would be interesting for developers,...
When I reset a node after it's provisioned but not configured, the p rovisioner would keep trying to configure it, and would not be able to provision any other nodes.
...
Hello,
I am trying to 'recover nRF52840 dongle after accidental UICR erase' as described here I did modify my dongle as described here
Unfortunately I do not know how...
Hello,
NRF52840
SDK 15.3.0
SoftDevice: s140
OS: Ubuntu
IDE: SES
I am having difficulty getting consistency out of the RTT + NRF_LOG_INFO() print statement. It...
Hello,
I use the nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31 with nrf52840-DK.
I'm looking for a way to get the transmit state after I sent a udp packet. I would like...
Hi,
we've been trying to reduce power consumption do I able to connect unused pins to GND directly?
Trace 1,2,3,4 do I able to connect to the GND?
Thanks, in advance...
Hi,
I am the first time programming with nordic and Segger. As I received the Thingy91 I just the getting started assistent to set up the toolchain.
This worked fine so...
